Most of the damage starts by partially lifted roof coverings, blown out eaves, and soffits. This leads to water entry, drywall saturation and damage to your belongings. Once the roof has been breached, the hurricane force winds can rip your home apart piece by piece as the wind pressure acts on the inside of the building envelope and when it finds a weak point the house implodes.
Yes, the Secure-Lock Structural Insulated Panels (SIPs) can survive. The metal skin on the panel acts as an integral moisture and vapor barrier, blocking rain damage even if shingles or other roof coverings are blown off. The metal skin on the underside of the panel creating the eave is water proof and practically indestructible, preventing wind driven rain damage. Each panel is part of an integrated system that prevents winds up to 150mph from grabbing hold of any structural components to open up the housing envelope. The panels go through extensive and rigorous quality control testing to ensure they meet and exceed building code requirements for wind, impact, racking, live and dead loads. Hurricane testing has shown our steel insulated panels to be stronger than block or wood frame construction, sustaining only very minor exterior siding damage in winds exceeding 140 mph, with no structural failures.
High Performance Green Building
Environmental concerns & carbon footprint recognition started the focus on green building, Energy Star ratings, and solar panels. Using energy efficient components and recycled materials that save more energy than they cost to produce is a net gain for your wallet and the environment.
All job site waste is recyclable! Expanded polystyrene is 100% recyclable as is all metal job site scrap. Steel is the most recycled material on earth. Over 80% of the steel used today is recycled!
40-60% reduction in energy costs compared to a wood frame or masonry built homes!
Secure-Lock Steel Panel Homes save $$$ due to a significant reduction in temperature from outside to inside the building envelope. A/C units are downsized for additional efficiency in these airtight shells.
Compared to a building envelope constructed of conventional wood frame 2″ x 6″, Secure-Lock Steel SIPs can form a shell that has 58% better thermal performance and a whole-wall R-value equal to 98% of its clear-wall R-value. This means the Secure-Lock steel SIP creates one of the tightest building envelopes in construction.
Secure-Lock Steel SIPs meet the requirement to be used as non-combustible exterior walls as defined by the IRC and ICC Codes!
Results of ASTM E 84 have shown that the Secure-Lock panel has a superior flame spread index of 5 and a smoke development index of 170, making the panel a Class A fire rated product. When exposed to fire, the panels produce less smoke than wood and do not allow the fire to spread. Secure-Lock steel panels do not “off-gas” as they are completely inert. A Secure-Lock steel SIP home is actually safer than a wood frame home. The inner and outer steel skins are continuous and even act as a ground in a lightning strike. Unlike wood, steel is an excellent conductor, offering far less resistance than wood to the current, thus generating much less heat.
Yes! We can walk you through every step of designing your home. The unique nature of our building system makes all design styles possible!
Absolutely! The building frame is steel and integrates with all modern constructions materials and finishes.
ASTM E 84 characterizes the relative rate at which flame will spread as the subject material burns. This test method is often referred to as the “Tunnel Test” because the test chamber is a nominal 25-foot-long by 20-inch wide chamber. A gas burner is lit at one end of the chamber and a draft is applied to facilitate flame propagation along the specimen. A photometer and light source is placed at the exhaust end of the chamber to measure the relative amount of smoke that is developed during the test. The test is run for 10 minutes and the distance that the flame propagates during that time is measured and used to compare to a standard. The Flame Spread Index calculated is a relative indication of the flammability of the test material with respect to a red oak standard. Both the distance of flame spread and the time-rate of flame spread are considered as part of calculating a flame spread index. Overly simplified, a reported flame spread index of 25 indicates that a material has approximately 25 percent of the standard material’s flame spread characteristics. The “smoke developed index” is calculated similarly. Section 803.1.1 of the International Building Code defines three classes of materials based on ASTM E 84 test results. Secure-Lock panel has a superior flame spread index of 5 and a smoke development index of 170, making the panel a Class A fire rated product.
|Flame Spread Index||Smoke Developed Index|
|Class A||0 – 25||0 – 450|
|Class B||26 – 75||0 – 450|
|Class C||76 – 200||0 – 450|
A combustible material is required to conform to the Class A requirements to be used in noncombustible exterior wall construction.
Eco-$mart, Inc is a
Service-Disabled Veteran-Owned Business